Australian outdoor project tools

Decking Calculator Australia

Use this free Australian decking calculator to estimate deck area, decking boards, board gaps, linear metres, waste, stock-board quantity and optional material cost from simple metric dimensions.

Deck dimensions

Enter the direction the boards will run as the deck length. Use your actual board width, spacing and available stock length.

metres (m)

metres (m)

millimetres (mm)

millimetres (mm)

metres per board

percent (%)

AUD per linear metre

Decking estimate

Results update as you change the inputs.

Deck area20.00 m²
Board courses across deck28
Net board length140.00 lm
Board length including waste154.00 lm
Pooled-length stock-board estimate29 boards

A theoretical minimum if offcuts can be reused efficiently; not a cutting schedule
Course-aware alternative (no offcut reuse)31 boards

Counts full stock lengths needed per course, then adds waste; can overestimate when offcuts are reusable
Approx. coverage per course145 mm
Estimated board material cost—
Layout matters: this is a quantity-planning estimate. Staggered joints, picture framing, breaker boards, stairs, mitres and unusable offcuts can change the number of stock boards you need.

How the decking calculation works

Deck area = length × width
Board module = board face width + gap
Board courses = ceiling((deck width + gap) ÷ board module)
Net linear metres = courses × board run length

SiteSum applies your waste allowance to the calculated lineal metres and shows two stock-board estimates. The pooled-length estimate assumes usable offcuts can be combined efficiently. The course-aware alternative assigns whole stock boards to each board course before adding waste, without counting reusable offcuts. Neither replaces a cut list; the actual purchase quantity depends on joint positions and supplier lengths.

How many decking boards do I need? A worked example

For a 5 m × 4 m deck with 140 mm board face width, 5 mm gaps and 5.4 m stock boards, using a 10% waste allowance:

  1. Board courses: ceiling((4,000 + 5) ÷ (140 + 5)) = 28 courses.
  2. Net decking: 28 × 5 m = 140 lineal metres.
  3. Including waste: 140 × 1.10 = 154 lineal metres.
  4. Pooled-length estimate: ceiling(154 ÷ 5.4) = 29 stock boards, assuming efficient reuse of offcuts and permitted joints.
  5. Course-aware alternative: 28 full-length courses × 1 stock board per course, plus 10% = 31 boards when short offcuts are not reusable.

These two figures differ because a 5 m run cut from a 5.4 m stock board leaves only 0.4 m. Buying 29 boards can be unrealistic if the design does not permit offcut reuse. Confirm the actual cutting layout with your installer before ordering; picture-frame borders, stairs, complex shapes and defects are additional.

For cutting strategies, staggered joints and more detailed take-offs, see our Australian decking board quantity guide.

Board width and gap

Use the installed face width of the decking board and the intended spacing for your actual product and project. Timber and composite products can have different installation requirements, so the calculator leaves both values editable rather than assuming one universal spacing.

Decking calculator FAQs

Which direction should I enter as deck length?

Use the direction the decking boards will run as the deck length. The other dimension becomes the width across which SiteSum counts board courses.

Does this calculate joists or bearers?

No. This page estimates decking boards only. Structural framing depends on spans, loads, timber or steel grade, support conditions and design requirements, so joists and bearers should be calculated separately from the applicable design information.

Why is the stock-board quantity only a planning estimate?

The pooled-length result assumes efficient offcut reuse, whereas the course-aware alternative assumes none. Use the actual board run, stock lengths, permitted joint positions and a cutting list before ordering. Picture-frame borders, stairs, mitres or damaged boards may add material beyond either simplified estimate.

Browse more SiteSum material calculators →

Expert guide: See How Many Decking Boards Do I Need? A Board-Module Method for Australian Decks for a deeper explanation of gaps, stock lengths, cut efficiency and waste.

Planning estimate only: verify board dimensions, spacing, stock lengths, fixing requirements, layout and supplier quantities before purchasing materials or constructing a deck.